Asked by: Edgard Elies
Asked in category: style and fashion, mens sportswear
Last Updated: 3rd May 2024
Can you put crown molding on popcorn ceilings?
Crown molding is a popular way to hide the seam between ceiling and walls. This can also be used for popcorn ceilings. If you have an popcorn-textured roof_, don't be afraid . It is possible to install crown molding with a popcorn ceiling, but it requires a little more care.
So, is crown molding possible on a textured ceiling?
Although the basic process is identical, crown molding shouldn't be installed against the wall. The wall and ceiling must be flat to allow crown molding to fit. However, crown molding should not be installed on top of popcorn ceilings.
You may also be curious about the size of nails you use to crown mold. A crown is usually nailed with a 2a nail, a compressor and a finishing gun. Brad nails are used to finish outside corners. Studs are usually 3-1/2a, drywall is A 1/2a, and crown molding is a minimum A 1/2a. Therefore, 2a finishing nails will be required.
How do I close the gap between crown moldings and ceiling?
A thin layer of caulk can be placed between crown moldings and ceilings to create a professional appearance. It will hide cracks and gaps. You can paint the caulk to match the ceiling and molding so it doesn't even show up. The molding appears flush with the ceiling.
What type of nail gun is needed for crown molding?
Finish nailers are versatile tools that can drive either 15- or sixteen-gauge nails. These are useful for smaller projects, including crown molding, baseboards and cabinets, chair rails and decorative trim, millwork, hardwood flooring, and cabinetry.
17 Related Question Answers Found
Do you need to glue crown molding?
Work to the right
That makes the crown molding easier to hold and the cut mark easier to see. Use construction adhesive on all rail—even where you can nail into studs and ceiling joists. That way, you can use just enough nails to hold the trim in place until the adhesive sets, and you'll have fewer nail holes to fill.Do you have to nail crown molding into studs?
Crown Molding
Most of the time there is no need to hit the vertical wall studs with the nails because the top 3 inches of the wall framing feature two horizontal ceiling plates, each 1-1/2 inches thick. If you're attaching the molding below the top 3 inches of the wall, insert the nails in the wall studs.Which side of crown molding goes against the ceiling?
Crown molding can look good both ways: in its usual alignment or upside-down, which makes it difficult to determine the end that's supposed to be the top. Generally, the end with the least amount of detail goes on top, and the decorative trim faces the bottom.
Do you need backer board for crown molding?
Crown molding is usually nailed to the wall studs along the bottom edge and into the ceiling joists above--a lot of stud-finder work. I skip all that by installing a plywood backer board to the top plate (the horizontal framing member above the wall studs).
How do I start crown molding?
crown moulding
- Step 1: Plan Your Installation.
- Step 2: Measure the Room and Mark the Stud Locations.
- Step 3: Put the Moulding Against a Framing Square.
- Step 4: Begin at the Wall Opposite the Door.
- Step 5: Lay out the Cope Joint.
- Step 6: Set up the Miter Saw.
- Step 7: Undercut along the Profile with a Coping Saw.
- Step 8: Test-Fit the Cut.
Do you paint crown molding before installing?
Painted Walls
You can paint the walls before or after installing the molding. However, painting prior to installing the molding has an advantage in that you do not need to protect the molding with painter's tape and can paint more quickly without worrying about getting paint on your molding.Why is there a gap between crown molding and ceiling?
Crown molding ceiling gap happens because the rough lumber behind the drywall shrinks. It can be prevented by nailing the ceiling molding to the ceiling allowing it to float up and down on the wall. Another key point is the outside temperature and humidity is much different in South Carolina during the year.
Why is crown molding separating from the ceiling?
Humidity and extreme changes in temperature can lead to molding beginning to detach from walls or the ceiling. Gaps and cracks develop, making the crown molding separate from the wall. When the trusses contract, the ceiling lifts and pulls up the crown molding creating separation, gaps or cracks.
Should I use crown molding?
It is fine to have it in some rooms, while not using it in others. Certain rooms in the house are almost always a desirable place for crown molding. If you have cathedral or vaulted ceilings, a typical crown molding will probably not fit or look good.
Does removing popcorn ceiling increase home value?
That said, the value gained by removing a popcorn ceiling does increase considering buyers' expectations for homes of a certain size and in a certain price range. Schutte estimates that removing a popcorn ceiling would add $25,000 to $35,000 in value for a large estate executive home.
How do I get rid of popcorn ceiling fast?
For easier scraping and practically no dust during popcorn ceiling removal, use a garden pump sprayer to mist the ceiling and let it soak in for about 15 minutes before scraping. Only give it a light misting—too much water could damage the drywall or loosen the joint tape.
How much does it cost to get rid of popcorn ceiling?
Popcorn Ceiling Removal Cost. The average cost to remove popcorn ceiling is between $1,010 and $2,260 with most homeowners spending about $1,710. Contractors typically charge $1 to $2 per square foot for removal of popcorn ceilings.
Should I remove popcorn ceiling?
It's not prohibitively expensive to remove, so you might want to simply get rid of the ceiling if everything else about the property really is perfect, Workers might scrape away the mess to reveal beautiful plaster perfectly intact underneath. But a popcorn ceiling more commonly covers up a bad drywall and mudding job.
How long does it take to scrape popcorn ceilings?
If you go with traditional methods — that is, scraping and removing, then resurfacing your ceilings — and hire a professional, you can expect approximately 20 hours of work to remove and replace your popcorn ceiling a 500sq foot area.
How hard is it to scrape off popcorn ceiling?
To make scraping off the popcorn texture easier, experts suggest lightly misting the ceiling with a garden pump sprayer. Work in small 4-inch-by-4-inch sections and let the water soak in for about 15 minutes. If the texture hasn't softened at all, lightly mist the area again and wait another 15 minutes.
What is the purpose of popcorn ceilings?
It was used from the 1950s to the late 1970's. It was sprayed on, creating a texture that was used to hide imperfections AND was believed to help with sound insulation. They quit widely using it when the asbestos was banned in the late 70's.
What's wrong with popcorn ceilings?
Some people think the popcorn ceilings have asbestos and are dangerous. Some of the 1950s and 1960s popcorn had asbestos, but these ceilings emit no vapors or fumes that can be inhaled. As long as they are covered with paint, and you don't disturb and breath the dust, you are not exposed to anything toxic.
Similar Asks
Trending Questions
Co-authors
4
Updated On
3rd May 2024
Views
1499
37
Questions
20
Answers
3
Videos
16
Users
95% of readers found this page helpful.
4.9/5
Rate this post by clicking on a star above
Thank you for your vote!